Skip to content
Layer X
Get a quoteWhatsApp
TechnologyPublished 14 Nov 2026 · Updated 3 Nov 2026

Copper 3D Printing With Green Lasers for Cold Plates

Copper 3D printing got a boost at Formnext Asia Shenzhen 2026 with green lasers. What it means for cold plates, EV parts and Indian design teams.

Layer X Team
Layer X Editorial Team
7 min read
Share

Say an Ahmedabad team is designing a power module for an EV charger, and the aluminium heat sink keeps missing its thermal target. Copper conducts heat far better than aluminium, so the obvious question is whether copper 3D printing can make a cooler with internal channels. Until recently the answer was awkward, because copper reflects the infrared light that most metal printers use. At Formnext Asia Shenzhen in August 2026, several Chinese makers showed green-laser machines built for exactly this problem, aimed at AI-server cold plates and other thermal parts. Layer X does not print copper, and we did not attend the show. This guide explains the technology from published reports and shows how Indian design teams can prepare, including form and fit prototyping before any metal is ordered. For the full show round-up, see our TCT Shenzhen 2026 highlights.

What Was Shown at Formnext Asia Shenzhen 2026

The show ran 26 to 28 August in Hall 15 at Shenzhen World, alongside PCIM Asia Shenzhen, a power electronics event. The organiser's final report counts 330 exhibitors and 34,202 visitors, and its programme included a forum on data-centre cooling. Three copper-capable systems stood out in the trade reports.

SystemMakerReported focus
Dual-green-laser systemAddireenFull-bed production of copper cold plates for GPUs, CPUs, memory and optical modules and automotive power electronics
M420G (dual laser)Han's Matrix3DMass production of copper and other thermal management components
DiMetal-300GLaseradd, a Kings3D subsidiarySingle-mode green-laser system for pure copper, copper alloys and other highly reflective materials

Addireen said its AI-server and IGBT cooling products were moving into batch production. That is the company's own statement, so treat it as a claim until customers confirm it.

Why Infrared Lasers Struggle with Copper

Most metal printers use an infrared laser. Pure copper reflects most of that light, so only a small share of the energy goes into melting the powder. Addireen, quoted by 3DNatives, puts infrared absorption in pure copper at under 10%. To compensate, printers push the power up, and that causes trouble.

QuestionInfrared laserGreen laser
Absorption by copperVery lowMuch higher
Typical problemSpatter, porosity, reflected light reaching the opticsWider process window, according to the maker
Effect on the partLower density and lower conductivityDenser, more conductive parts, according to the maker

The 3DNatives article is promotional and the performance claims come from the manufacturer. Green light is absorbed far better by copper, which is why these machines target copper and other reflective metals. Independent test data on printed copper parts is what a careful buyer should ask for.

In plain terms, a green laser lets the printer use a gentler setting and still melt the copper, so the melt pool is easier to control. That matters for cooling parts, because tiny pores and rough internal walls reduce heat flow and can cause leaks. Whether that advantage holds across a full production run is exactly what the repeat orders will show.

Why AI Servers and EVs Are Driving Copper 3D Printing

3DPrint.com links the interest to heat. Higher compute density creates more heat, and additive manufacturing can make internal channels and heat-transfer structures that are hard to machine. The same trade press names several demand areas:

  • AI-server cold plates: liquid cooling for GPUs, CPUs and memory modules.
  • Power electronics: cooling for IGBT modules and automotive power electronics.
  • EV and energy: thermal management parts for new-energy vehicles.
  • Busbars: high-current copper parts are a related use. No report we opened shows printed busbars, so treat this as a possibility.

A cold plate on a stand is not a market. Watch for repeat orders and qualified part numbers, not more prototypes at exhibitions.

That rule of thumb follows the 3DPrint.com author's own caution that another supplier of green-laser machines does not prove AI cooling has become a large additive manufacturing market.

Designing for Cooling Before You Choose a Process

Design the cooling path before you pick copper printing, forging or brazed plates. Printing lets you route channels through the part, but the design still has to work in the real world.

Start with the heat load, coolant, pressure drop and available space. Then check that every channel can be cleaned of loose powder, since a dead-end passage traps it. Keep wall thickness realistic, plan machined sealing faces and port threads, and decide which surfaces need finishing. Our guide to 3D printing for electronics enclosures covers thermal management and connector integration from the enclosure side.

Also decide early how the cooler will be tested. Agree the flow rate, the pressure the plate must hold and the leak check before drawings are released, so the supplier knows what to prove. For a typical Gujarat electronics or EV team, the cheapest saving is a frozen interface: if the mounting holes, ports and keep-out zones do not move, the internal channel design can be improved without redoing the whole assembly.

Prototype the Geometry First: Where Layer X Can Help

Be clear about the limit. A plastic prototype cannot show how well copper will move heat, because plastic does not conduct heat like copper. What it can prove is everything around the cooler: envelope, port positions, hose clearance, mounting points and assembly order. Those mistakes are cheap to find in plastic and expensive to find in copper.

  1. Define the heat load, coolant and space available.
  2. Model the channels in CAD and run a simple flow or thermal check.
  3. Print a form and fit model. SLA resin printing suits fine port and channel detail, and SLS nylon printing suits tougher fit-check parts.
  4. Fix clearances and assembly problems while changes are still cheap.
  5. Ask a copper-capable supplier for a feasibility review of the frozen geometry, and compare it with a machined and brazed route.

Questions to Ask Before Paying for Printed Copper

  • What density and conductivity do you measure, and can I see the test report?
  • How rough are the internal channels, and how do you clear powder from them?
  • Will each plate be pressure tested for leaks?
  • Is this a repeat, qualified part number, or a one-off sample?

Key Takeaways

  • Green lasers fix an absorption problem: copper reflects most infrared light, and green light is absorbed far better.
  • Claims need proof: performance figures come from machine makers, so ask for independent test data.
  • Heat drives demand: AI-server cold plates and power electronics are the lead applications.
  • Design first: plan powder removal, sealing faces and flow before choosing a process.
  • Prototype the surroundings: plastic models prove fit and assembly, not thermal performance.

Frequently Asked Questions

Why is copper hard to 3D print?

Copper reflects most infrared laser light, so a standard metal printer struggles to melt it cleanly. Raising the power can cause spatter and porosity and can send reflected light back to the optics. Green lasers are absorbed much better by copper, which is why they are now being used.

Does Layer X offer copper 3D printing?

No. We do not print copper and we do not use green-laser machines. We offer DMLS metal printing in other metals, SLA resin, SLS nylon and FDM, so ask us which fits your prototype stage.

Are printed copper cold plates already in mass production?

One maker says its AI-server and IGBT cooling products are moving into batch production. An analyst at 3DPrint.com cautions that the market needs repeat orders and qualified part numbers before it counts as proven.

Can a plastic prototype test cooling performance?

No. Plastic does not conduct heat like copper, so it cannot show real thermal results. It can confirm fit, port positions, clearances and assembly before you commit to metal.

Why Layer X for Thermal-Part Prototyping?

Layer X is a studio in Satellite, Ahmedabad, shipping across Gujarat and India. We cannot print copper, but we can help you get the surrounding geometry right first: SLA resin prototypes in 2-4 days and SLS nylon in 4-6 days, with an engineer reviewing your file and a quote within 24 h. There is no minimum order, so a single fit-check model is fine. If your part needs copper, we will say so plainly and help you prepare a clean, frozen design for a copper-capable supplier. WhatsApp us on +91 93283 10466 or Get your 24-hour quote

Sources & Further Reading

  1. 3DPrint.com — Formnext Asia Shenzhen 2026: China has built the AM stack, what comes next
  2. 3DNatives — Using a Green Laser Facilitates 3D Printing of Pure Copper and Copper Alloys
  3. VoxelMatters — Formnext Asia Shenzhen 2026 closes with record attendance, up 65%
  4. Formnext Asia Shenzhen — Final report 2026
Layer X TeamLayer X Editorial Team

Technical content produced by the Layer X manufacturing team — engineers, quality specialists, and process experts with direct, hands-on experience.

Layer X services in this article
DMLS Metal 3D PrintingSLA Resin 3D PrintingFDM 3D Printing
Start a project

Need a quote for your next project?

Upload your CAD file and get a precision manufacturing quote within 24 hours.

Get a Quote
More from Technology

Continue reading

Technology

3D Printed House in India: Where Construction Printing Stands

Is a 3D printed house in India realistic yet? How construction printing works, what has been built, what still limits it and the questions to ask first.

Read article
Technology

Multicolour 3D Printing in 2026: Toolchangers and Purge Waste

Multicolour 3D printing in 2026: toolchangers, multi-nozzle and multi-spool machines, the purge-waste trade-off, and what it means for mock-ups and models.

Read article
Technology

Multi-Laser Metal 3D Printing: What China Showed in 2026

Multi-laser metal 3D printing with 16 to 256 lasers headlined TCT Asia 2026. See what it means for Indian buyers and when DMLS beats casting.

Read article